Asr 9000 Nv Satellite Support For Mac

1. Asr 9000 Nv Satellite Support For Mac Mac
2. Asr 9000 Nv Satellite Support For Mac Pro

How to check the arp when the satellite has auto ip configured? Sh arp vrf.nVSatellite RP/0/RSP1/CPU0:9K-MSN1#sh arp vrf.nVSatellite - 0/0/CPU0 - Address Age Hardware Addr State Type Interface 10.0.0.1 - 6c9c.ed0d.8080 Interface ARPA Bundle-Ether400 10.1.144.1 - 8478.ac06.c1e0 Satellite ARPA Bundle-Ether400 RP/0/RSP1/CPU0:9K-MSN1# 2. How to ping the satellite when it is auto ip configured? Use “ show nv satellite status brief” command to get the satellite ip address ping vrf.nVSatellite can be used to ping the auto ip RP/0/RSP1/CPU0:9K-MSN1#show nv satellite status brief Sat-ID Type IP Address MAC address Status - - - - - 400 asr9000v 10.1.144.1 8478.ac06.c1e0 Connected (Act) RP/0/RSP1/CPU0:9K-MSN1#ping vrf.nVSatellite 10.1.144.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.1.144.1, timeout is 2 seconds:!!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms RP/0/RSP1/CPU0:9K-MSN1# 3. How to login to the satellite from ASR9k console if we have auto-ip configured?

Cisco ASR 9000 Architecture Dennis Cai, ERBU Technical Marketing Architect. ASR 9000 “nV System” ASR 9000v ASR 9000 ASR 9000v nV Satellite nV cluster Network Cloud Client Simplify Operations Reduce overall TCO Integrated A to Z Management.

Take the satellite IP address from the 'show nv satellite status brief' output. Telnet vrf.nVSatellite from asr9k console can be used to login to the satellite. Is there any command that displays the ICLid, sat ip address and host ip address on the satellite?

Following commands can be used to get these info: show satellite discovery show satellite control show satellite iclidinfo active 5. How to retrieve satellite shelf inventory info (SFP types and serial numbers etc) from the 9K? ' show inventory' under admin mode. RP/0/RSP0/CPU0:nv-cluster-escalation(admin)#sh inventory - - NAME: 'module SAT200/0/CPU0', DESCR: 'ASR-9000v GE-SFP Line Card' PID: ASR-9000v, VID: N/A, SN: NAME: 'module mau GigabitEthernet200/0/CPU0/0', DESCR: 'CISCO ' PID: GLC-SX-MMD, VID: V01, SN: AGA1747RC2F 6.

Discuss email privately. Invite teammates to discuss specific email and threads. Ask questions, get answers, and keep everyone in the loop. The new Spark feels like the first product that may finally solve email communication and assignments for the MacStories team. Spark email for mac.

How to transfer/activate image to all satellites from host? Install nv satellite transfer all install nv satellite activate all 7. How to check if the image transfer is complete on the satellite after the image transfer is initiated on ASR9K to the satellites? Check the output of “ show nv satellite status brief”. RP/0/RSP0/CPU0:HOST1#show nv satellite status brief Sat-ID Type IP Address MAC address Status - - - - - 500 asr901 100.100.1.2 c464.13b0.ce74 Connected (Act; Transferred) 600 asr901 100.100.1.3 c464.13b0.cab4 Connected (Act; Transferred) 700 asr901 100.100.1.4 7cad.7404.7c70 Connected (Act; Transferred) 800 asr901 100.100.1.5 4403.a7f9.80ec Connected (Act; Transferred) RP/0/RSP0/CPU0:HOST1# 8. How much time does it takes for image transfer? Typical times for image transfer for 9000v is about 3-5 mins and for 901 is 4-6 mins.

What are the confreg values for satellite ASR9000v in the following scenarios? To select the image in flash during reload command: 0x101 To get the image from flash during activate from asr9k: 0x101 10. What are the confreg values for satellite ASR901 in the following scenarios? To select the image in flash during reload command: 0x2042 To get the image from flash during activate from asr9k: 0x2042 11. How to check if the crosslink on the satellite is formed or not?

Asr 9000 Nv Satellite Support For Mac Mac

LC:Satellite#show satellite crosslink Gi0/10 Interconnect Link: GigabitEthernet0/10 xosif: 6 iclid: 10 hostid: 0 cpvlan: 0 Link State: Up SDAC State: Discovered Crosslink State: Up - Access Port Link State ForcedDown? - Gi0/0 Down No No Gi0/1 Down No No Gi0/2 Down No No Gi0/3 Down No No Gi0/4 Down No No Gi0/5 Up No No Gi0/6 Down No No Gi0/7 Up No No Gi0/8 Down No No Gi0/9 Down No No - LC:Satellite# 12. Is Serial number Mandatory?. Hub And Spoke: Not Mandatory.

Simple Ring: Mandatory. Dual Home: Mandatory. L2Fab: Mandatory 13. How many VRF Licenses are required for auto-ip? One per host(if dual head) 14.

What is port partitioning means? Port Partitioning defines the mapping range of satellite access ports to different ICLs on Host. In case of 9000v we have 44 ports and can have mapping 0-20 to one ICL and 21-43 ports to another ICL on host.

Which all ports are ICL ports in 9000v? Four 10Gig ICLs: 1/45 – 1/48 16.

Which all ports are ICL ports in 901? Two 1Gig ICLs: Gig0/10 & Gig0/11 17. Is 1G ICL supported on 9000v?

Yes, ports ten 1/45 and ten 1/46 can be used as 1G ICL by inserting 1G SFP 18. Can 10G and 1G ICL be used together in 9000v?

Ten 1/45 is using 1G SFP while ten1/46 is using 10G SFP 19. Can 10G port on the 901-AC-10G chassis be used as ICL? No, the 10G ports can neither be used as ICL nor as Access ports in 5.1.1 release 20. How to debug if there is an issue with satellite specific traffic drops? Please debug the drops on the satellite using 21.

The satellite crashed while doing some config changes. How to debug this? Collect the crashinfo dumped in the flash of the satellite.

Decode the traceback and involve the appropriate team to triage this further. What is the support for different connectivity options in 5.1.1 release? The following topology options are supported. Direct connectivity – “Hub and Spoke”.

Chains of Satellites with single host. Ring of satellites with dual host. L2FAB. Dual Homing The following topology options are not supported:. Branched Networks. Network with Loops. Simple Ring over L2FAB.

Simple Ring with both ends terminating on same host 23. Which Satellite devices supports the new 5.1.1 release topologies? ASR9000v and ASR901 24.

Do we support ISSU upgrade for satellite? Can we run SNMP query for Satellite ICL interface? How many satellites do we support when connected as Hub and Spoke topology for Cluster and non-Cluster node?

Simple Ring 1. How to check which icl port of satellite is connected to the other icl port of the next satellite in the simple ring topology? How to check if the ICCP group is up or not in Dual Home? Check the output of “ show iccp group ” which gives the details.

How to check if the orbit has come up or not in Dual Home Check the output of “ show nv satellite protocol redundancy” which gives the details. What are the limitations with respect to satellite Dual-home pairing?

A satellite can only be connected to two hosts A host can only be in one dual-home pairing 4. Is port partitioning supported in Dual Home? What would be the IP addresses for Active and Standby in case of DH topology with auto-ip? Active host will have 10.0.0.1 and Standby-host will have 10.0.0.2 6.

Is bundle ICL supported on Dual Home topology? Does satellite automatically reroutes to standby host incase of Primary host failure. How much time does it takes for traffic convergence? The satellite automatically reroutes to the other ASR9K host incase of Primary host failure.

Asr 9000 Nv Satellite Support For Mac Pro

We should see sub-second convergence for L2 traffic. For L3 the convergence will be dependent on the routing protocol. Does the satellite reverts back to the active host incase the active host comes back up after failure.

The satellite reverts back to the active host incase the active host comes back up after failure. Please note that the satellite status on the active host should be 'Connected', otherwise the satellite will not revert back to the Previous Active host. For PE Isolation switchover, will a Dual home switchover be triggered if the backbone interface was still up and only the IGP goes down for some reason? No, the PE isolated DH switchover only triggers when the link goes down physically or is administratively shut on the Active Host. It is not triggered if the IGP goes down on the backbone interface but the link is up.

What is the configurable VLAN range on the L2fab link in case of ASR9000v/ASR901 platform? 9000v: 4092 (VLAN 1 & 4094 are reserved for internal usage) 901: 4093 (VLAN 1 is reserved for internal usage) 2. What are the encapsulation types supported on L2Fab links? 802.1q & 802.1ad 3. Is bundle ICL supported in L2fab topology? Is auto-IP supported in L2fab?

Is Dual Home supported in L2fab? Is port partitioning supported in L2fab? Is CFM on ICL link mandatory for L2FAB? No, but without CFM convergence for DH SO will be very slow(30 secs).

To achieve subsec convergence it is recommended to use CFM on the ICL link 8. Can we use same VLAN ID on both Hosts in L2fab-DH topology? Yes, but only when 2 physical ICL links are used on SAT where each ICL is mapped to different hosts. Refer to L2FAB supported topologies 9. What is the VLAN-ID and encap-type to be used in case of single ICL link on SAT?

In case of single ICL on SAT we need to make sure different VLAN ID and same encapsulation type are used on the L2fab links on Hosts 10. Can we use different encap-type on the L2fab links on Hosts in L2fab-Dual Home topology? But make sure 2 physical ICLs are used on SAT, one for each Host.

How to Check active ICL on Satellite with corresponding sdac state on it? Supported L2Fab Topology(5.1.1 release) Single Home 1. Single Physical ICL on Host and Satellite 2. Multiple Satellites with Same Host 3.

Mutlitple Satellites with same hosts having multiple ICLs 4. Co-existence of L1 and L2FAB on host Dual Home 1. Single Physical ICL on Hosts as well as Satellite 2. Single Physical ICL on Host and Multiple ICLs on Satellite 3.

Dual Home with Multiple Satellites and Single ICL - Abhisek Jhunjhunwala, S/W Engineer, ASR9000 Ram Mohan A M, S/W Engineer, ASR9000 Santosh Sharma, CCIE #40773 S/W Engineer, ASR9000 Sowmya L S/W Engineer, ASR9000. Thanks, Santosh: Here's my config: Host A: RP/0/RSP0/CPU0:XXXXXX#show run redundancy Thu Mar 26 07:03:43.371 UTC redundancy iccp group 200 member neighbor X.X.X.X!!!! RP/0/RSP0/CPU0:XXXXXXX# RP/0/RSP0/CPU0:XXXXXXX#show run nv Thu Mar 26 07:04:23.472 UTC nv snip! Satellite 200 type asr9000v ipv4 address 10.255.255.200 redundancy host-priority 32! Serial-number XXXXXXX!! RP/0/RSP0/CPU0:XXXXXXX# interface TenGigE0/0/1/1 description XXXXXXXX cdp vrf satmgmt ipv4 point-to-point ipv4 unnumbered Loopback100 nv satellite-fabric-link satellite 200 redundancy iccp-group 200! Remote-ports GigabitEthernet 0/0/0-4!!!

Host B: RP/0/RSP1/CPU0:XXXXXX#show run redundancy Thu Mar 26 08:18:53.495 CST redundancy iccp group 200 member neighbor X.X.X.X!!!! RP/0/RSP1/CPU0:XXXXXXXX#show run nv Thu Mar 26 08:19:19.411 CST nv snip satellite 200 type asr9000v ipv4 address 10.255.255.200 redundancy host-priority 64! Serial-number XXXXXXXX! RP/0/RSP1/CPU0:XXXXXX# RP/0/RSP1/CPU0:XXXXXXX#show run int TenGigE0/0/1/1 Thu Mar 26 08:20:30.220 CST interface TenGigE0/0/1/1 description XXXXXXXX cdp vrf satmgmt ipv4 point-to-point ipv4 unnumbered Loopback100 nv satellite-fabric-link satellite 200 redundancy iccp-group 200! Remote-ports GigabitEthernet 0/0/0-4!!! Santosh: Just as a follow up: I have the 'connected' status in the active host, always have. Hi, Santosh: Sorry for hogging the comments, but I wanted to ask you the following: my setup initially had all SATs connecting to one single host.

Then customer started dual-homing them. Since we had single-host connection we used a single IP address and the same Ip address for all hosts (9010, as ip unnumbered loopback). I'm not using auto-ip. If using static ip addressing on all SATs and having, at least one dual-homed, should the host ip be different in both active and standby hosts? Also, should i configure the static ip address of the DH sat differently in both the active and standby host (or can it stay the same)?